Enviro EF-III BAY I FPI Instrukcja Instalacji

1 SHERWOOD INDUSTRIES LTD. 6782 OLDFIELD ROAD VICTORIA, BRITISH COLUMBIA V8M-2A3 PELLET STOVE EF-III BAY i OWNERS TECHNICAL MANUAL MODELS FS, FPI a

ELECTRICAL COMPONENT FUNCTIONS The following is a list of electrical components and their functions on the ENVIROFIRE EF-IIIi Bay pellet stove. 1.

11. 160°F (71°C) TEMPERATURE SENSOR When this sensor (located on the left side firewall) reaches 160°F (71°C), the convection blower will go to high

DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE 1. Check clearances to combustibles. 2. Do not obtain combustion air from an attic, garage or any

REMOVING YOUR NEW STOVE FROM IT’S PALLET To remove your new stove from its pallet, open the left and right side panels. There are two wood screws t

MASONRY FIREPLACE INSERT INSTALLATION, MODEL FPI The Fireplace Insert model includes surround face plates and a pedestal. When installing this unit,

ASSEMBLING THE FACE PLATE FOR THE FPI AND BIH MODELS 1. To attach the pedestal, place the unit on its back, making sure not to damage the wiring, th

RECOMMENDED FRAMING FOR BUILT IN HEATER When installing model BIH it is recommended that you use the dimensions shown in the diagram below. These type

FREESTANDING INSTALLATION, MODELS FS CLEARANCES TO COMBUSTIBLES (FREESTANDING) - Side wall to unit A- 6 INCHES (150 mm) - Back wall to unit B- 1 INC

MODEL FS (FREESTANDING) INSTALLATION PEDESTAL INSTALLATION: Model FS comes with a pedestal that has to be attached prior to installation: - Remove

HORIZONTAL EXHAUST THROUGH THE WALL 1. NOTE: Use only listed type “PL” or “L” pellet venting products. Failure to use listed components may cause

ENVIROFIRE INSTALLATION MANUAL TABLE OF CONTENTS INTRODUCTION Important Safety Data... 3

THROUGH WALL INSTALLATION1” 20

FREESTANDING INSIDE VERTICAL INSTALLATION 1. Choose a stove location that is ideal. See the section Deciding Where to Locate Your Pellet Appliance.

FREESTANDING OUTSIDE VERTICAL INSTALLATION To accomplish the above titled installation, follow steps 1 through 8 in the previous section and then fin

MOBILE HOME INSTALLATION - Secure the heater to the floor using the two bolt holes supplied in the pedestal. - CAUTION: THE STUCTURAL INTEGRITY OF

TROUBLESHOOTING DO NOT: - Hold the start-up switch down, this is a momentary contact switch and can be damaged if held down too long. - Service the

4. The convection blower will not function normally - Check all the connections between the controller, switch, and the convection blower against t

placing a jumper across the pins. If the auger now cycles very quickly, test the dial-a-fire potentiometer. If the auger did not cycle then replace

WIRING DIAGRAM 27

PARTS LIST EF-001 AUGER MOTOR EF-088A LOG SET (20-036) EF-002 CONVECTION BLOWER EF-091 FPI BRASS TRIM EF-004 CONVECTION BLOWER IMPELLER EF-0

AUGER BRASS BUSHING SET OF TWOEF-065 PIN IGNITEREF-127 POWER UP TIMER EF-037 EXHAUST TEMP SENSOR 140°F (60°C) EF-010 COMBUSTION BLOWER COMPLETEEF-007

IMPORTANT SAFETY DATA Please read this entire manual before installation and use of this pellet fuel burning room heater. Failure to follow these in

EF 2/3 HOPPER LID WITH HANDLEEF-104 EF3Bi DECORATIVE TRIVET EF-150 PAINTEDEF-151 GOLD FPI OVERSIZED SURROUND EF-078 BIH OVERSIZE SURROUND EF-079 CONTR

WARRANTY Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one year warranty is provided on all electri

PELLET QUALITY IS IMPORTANT, PLEASE READ THE FOLLOWING PAGE Your pellet stove has been designed to burn wood pellets only. Since there are many man

WARNINGS AND RECOMMENDATIONS A. Do not abuse the glass by striking or slamming the door shut. B. Do not attempt to operate the stove with broken g

HOW TO START AND OPERATE YOUR PELLET APPLIANCE 1. Check and fill hopper with pellets. 2. Switch on power by pushing the start up switch once only. 3

SLIDER/DAMPER INSTALLATION /OPERATION INSTRUCTIONS This is used to regulate the airflow through the pellet stove. INSTALLATION 1. Remove the slider

AREAS FOR ROUTINE INSPECTION The following should be inspected periodically to ensure that the appliance is operating at its optimum and giving you e

DOOR GLASS (It is recommended that your dealer replace the glass if broken.) The door glass is made of 5 mm thick, high temperature PYROCERAMIC The c