Enviro EA800 Instrukcja Użytkownika Strona 53
- Strona / 98
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
D
-
011
-
0152
49
Operation
This chapter provides instructions for doing the following:
■ “Monitoring Environmental Conditions” on page 49
■ “Viewing Sensor Settings” on page 50
■ “Viewing Active Alarms” on page 50
■ “Viewing the Alarm Log” on page 51
■ “Viewing Pending Alarm Information” on page 51
■ “Viewing Limit Settings” on page 52
■ “Viewing the Event Log” on page 52
■ “Viewing the Sensor Log” on page 53
■ “Viewing Firmware Information” on page 53
■ “Viewing RF Information” on page 54
Monitoring Environmental Conditions
The current environmental conditions measured by each sensor connected to the EA800 base unit are shown on
the home screen. Depending on the current sensor status the home screen may be one of the following screens:
■ MONITORING screen: This screen is shown when there are no active alarms or pending alarms. This screen
displays the current readings from all programmed sensors as shown in the example below.
Note: Dashes indicate that a sensor has not been programmed yet.
■ MONITORING screen with pending alarm. A pending alarm indicates that
a sensor has exceeded the low or high limits but that the condition has
not exceeded the programmed delay (0 to 120 minutes). When an
alarm is pending, the sensor’s reading is displayed in reverse text as
shown in the example for wired sensor 2.
If conditions in the sensor’s area return to the non-alarm state within
the alarm delay time, the text returns to normal. If conditions remain
outside the programmed sensor alarm limits for longer than the delay
time, the screen changes to the ACTIVE ALARMS screen below.
■ .ACTIVE ALARMS Screen: This screen is displayed when conditions
monitored by any programmed sensor exceed one of its programmed
limits for longer than the programmed delay period. Only the active
alarm(s) is displayed as shown in the example below. See “Viewing
Active Alarms” on page 50 for the procedure to access alarm
information
This column shows
environmental readings
for wireless sensors 5-8.
This column shows
environmental readings
for wired sensors 1-4.
Sensor 1
Sensor 2
Sensor 3
Sensor 4
Current Date
Current Time
Sensor 5
Sensor 6
Sensor 7 (not installed)
Sensor 8 (not installed)
Pending alarm
- Installation/Owner’s Manual 1
- Table of Contents 3
- General Information 5
- How to Use This Manual 6
- Block Diagrams 7
- 4 D-011-0152 8
- Symbol Definition 8
- Monitoring Screens 9
- 6 D-011-0152 10
- Table 2 Key Functions 10
- Key Function 10
- Base Unit Connections 11
- Access Control and Passwords 12
- Humidity Sensors 15
- 4-20mA Sensors 15
- Multi-Function Sensors 17
- Contact Closure Sensors 17
- Water Sensors 17
- Sensor Parameter Descriptions 18
- 16 D-011-0152 20
- Relay Operation 20
- Preparation 21
- From 11-26 VDC 23
- Installation 25
- Install the Wired Sensors 26
- Install the Wireless Sensors 26
- + (-) + (-) + (-) 28
- Base Unit-Powered 29
- External Adapter-Powered 29
- Programming 31
- Example shown, set values as 32
- 30 D-011-0152 34
- Setting the Current Date 35
- Setting the Time 36
- Adding Wireless Sensors 37
- 34 D-011-0152 38
- 36 D-011-0152 40
- N.O. Contact or N.C. Contact 45
- 42 D-011-0152 46
- Adding Wired Sensors 47
- 44 D-011-0152 48
- Adding a 4-20mA Sensor 51
- Configuring the Relays 52
- Operation 53
- Viewing Sensor Settings 54
- Viewing Active Alarms 54
- Viewing the Alarm Log 55
- Viewing Limit Settings 56
- Viewing the Event Log 56
- Viewing the Sensor Log 57
- Viewing Firmware Information 57
- Viewing RF Information 58
- Maintenance 59
- 56 D-011-0152 60
- Adding a Sensor 61
- Replacing a Sensor 61
- Editing Sensor Parameters 62
- Reprogramming a Relay 63
- Deleting a Sensor 63
- Changing the Date Format 64
- Changing the Time Format 64
- Unlock the EA800 as shown 65
- Changing the Buzzer Setting 66
- Changing the Password 67
- Clearing the Alarm Log 68
- Clearing the Sensor Log 68
- Updating the Firmware 69
- Saving Configuration Settings 70
- LOAD/SAVE 71
- Exporting the Stored Logs 72
- Exported Event Data 73
- Exported Sensor Data 73
- 70 D-011-0152 74
- Troubleshooting 75
- Verifying RF Signal Strength 76
- Specifications 77
- Accessories 78
- Appendix A: Screen Maps 79
- 76 D-011-0152 80
- See Figure 20 81
- See Figure 21 81
- 78 D-011-0152 82
- 80 D-011-0152 84
- Dependent on format 85
- See Figure 25 85
- 82 D-011-0152 86
- 84 D-011-0152 88
- 86 D-011-0152 90
- 92 D-011-0152 96
Electrolux EKC60752X 400V manuály
Uživatelské manuály a uživatelské příručky pro Příslušenství pro míchačky / kuchyňské roboty Electrolux EKC60752X 400V.
Poskytujeme 1 manuály pdf Electrolux EKC60752X 400V ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Electrolux EKC60752X 400V Uživatelský manuál (76 strany)
Značka: Electrolux | Kategorie: Mixer/food processor accessories | Velikost: 1.71 MB |
Tabulka s obsahem
EKC60752
1
Innehåll
4
Säkerhet
5
Kylfläkten
12
Luckspärren
12
Stekning
21
~ 2 sek
24
~ 1 sek
24
Val Stopp+Go
25
~ 2 sec
26
~ 1 sec
26
~ 3 sec
26
Signalur
29
Ugnsdisplay
34
Signalur
37
Stopptid
39
Bakning
42
Matlagning
43
Stekning
44
INSTÄLLNING
45
Max Grill
46
Upptining
48
Stektabell
50
°C Falsläge
51
. Använd rak
56
Ugnsluckan
58
THIS SIDE UP
60
Skrotning
73
Další produkty a příručky pro Příslušenství pro míchačky / kuchyňské roboty Electrolux
| Modely | Typ Dokumentu |
|---|---|
| EKC60054X | Uživatelský manuál Electrolux EKC60054X Användarmanual, 48 stránky |
| EWF1284BR |
Uživatelský manuál
Electrolux EWF1284BR Používateľská príručka,
48 stránky
|
| ESJ4000 |
Uživatelský manuál
   
Electrolux ESJ4000 Ръководство за употреба [en] [fr] ,
68 stránky
|
| EKC60164X 400V | Uživatelský manuál Electrolux EKC60164X 400V Användarmanual, 44 stránky |
| EKI6151 | Uživatelský manuál Electrolux EKI6151 Användarmanual [pt] , 48 stránky |
| EKC6181A | Uživatelský manuál Electrolux EKC6181G Användarmanual, 28 stránky |
| EKC60155W 400V | Uživatelský manuál Electrolux EKC70155W 400V Användarmanual [bg] [sk] [sq] , 56 stránky |
| EKC7152 | Uživatelský manuál Electrolux EKC6152 Användarmanual, 28 stránky |
| ESI6261W | Uživatelský manuál Electrolux ESI6261K Användarmanual, 44 stránky |
| EKI6150 | Uživatelský manuál Electrolux EKI6150 Användarmanual, 48 stránky |
| EOK9837X | Uživatelský manuál Electrolux EOK9837X Användarmanual, 64 stránky |
| EOB64140X EU | Uživatelský manuál Electrolux EOB64140U EU Användarmanual, 68 stránky |
| EKC6181AC | Uživatelský manuál Electrolux EKC6181AC Användarmanual, 28 stránky |
| EKC60163W 400V | Uživatelský manuál Electrolux EKC60163W 400V Användarmanual, 44 stránky |
| EKC6122X | Uživatelský manuál Electrolux EKC6122X Användarmanual, 32 stránky |
| EKC60150X 400V | Uživatelský manuál Electrolux EKC70150X 400V Användarmanual [de] [en] , 48 stránky |
| EKC6254 | Uživatelský manuál Electrolux EKC6254 Användarmanual, 28 stránky |
| COOKER,EKE70012 230V | Uživatelský manuál Electrolux COOKER,EKE70012 400V Användarmanual [ru] , 36 stránky |
| EKC6182 | Uživatelský manuál Electrolux EKC6182 Användarmanual [en] , 28 stránky |
| EKD6144 |
Uživatelský manuál
Electrolux EKD6144 Ohjekirja,
56 stránky
|
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji